DP8005 SCOTCH-WELD 3M black adhesive for bonding plastics including PE and PP, 45 ml

Code: 7100089475
€45,40 / pcs €37,50 excl. VAT Measure price:
in stock (12 pcs)
Delivery to:
20.11.2026
Delivery options

3M Scotch-Weld DP8005 - Black Plastic Bonding Adhesive Including PE and PP, 45 ml

Detailed information

Product detailed description

3M Scotch-Weld DP8005 - Black Plastic Bonding Adhesive Including PE And PP, 45 ml

Unique adhesive for bonding low surface energy (LSE) plastics - polyethylene, polypropylene, and others, as well as for bonding other materials such as wood, glass, metal and concrete.

Adhesion without surface preparation. 3M™ Scotch-Weld™ 8005 structural adhesive can solve various problems commonly associated with bonding low surface energy plastics. In addition to a wide variety of plastics, it allows the bonding of a whole range of other materials with dissimilar substrates, such as metals, rubber, glass, ceramics and wood within a single-step process with minimal or no surface preparation. All substrates should, however, be clean, dry and free of coatings, oxide layers, oils, dust, mould release agents and other contaminants. Fast bonding with confidence. This medium-viscosity structural adhesive allows for good control and sufficient application across the entire surface. Thanks to the 10:1 mix ratio, it achieves a working time of up to 3 minutes. Handling strength can be achieved after approximately 3 hours and full curing after 24 hours at room temperature (22 °C). After the surfaces are joined, this adhesive exhibits excellent resistance to water and moisture while maintaining very good chemical resistance. It is an effective system for joining, potting and structural bonding that can replace screws, rivets, plastic welds and two-step processes involving chemical etchants, primer coats or surface conditioning in many areas of application. Recommended use: Joining plastics with metals, for example in the production or repair of appliances; bonding low surface energy plastics without the application of a primer coat; bonding impact-resistant composites; production or repair of various sporting goods; bonding low surface energy plastics such as polypropylene, polyethylene and thermoplastic elastomers; bonding with acrylates. Acrylic adhesives are two-part adhesives characterised by excellent strength and durability of the bonded joint, but with slightly lower adhesion than epoxy adhesives. However, they possess several properties that allow for easy use, such as much faster curing, higher tolerance to oiled or unprepared bonded surfaces and the ability to bond to a wide range of materials.

The adhesive has excellent resistance to moisture and very good chemical resistance.

Application using EPX dispensing pliers.

  • Two-component acrylic-based adhesive
  • Mixing ratio 10:1
  • Time to reach non-tackiness: 3-6 minutes
  • Handling strength time: 120-180 minutes at 23°C
  • Full strength time: 24 hours at 23°C

Application:
Mounting and Trim
Sealing, Potting and Encapsulation of Electronics
Bonding panels to frames and reinforcements to panels
Joining with small joints
Large Area Lamination Assembly
Product colour: Transparent
Full cure time: 8-24 Hours @ 72 F (22 C)
Working time: 3 minutes @ 72 F (22 C)
Industries:
Special vehicle
Metalworking
Advertisement
Woodworking
Shear strength: 2200.0 Pound_Per_Square_Inch
Storage temperature: 40 Degree Fahrenheit
Storage temperature (Celsius): 4 °C
Application temperature up to (Celsius): 80.0 Degrees Celsius
Application temperature from (Celsius): -55.0 Degrees Celsius
Hardness: 55-60 Shore D
Indoor/outdoor: Both
Container size (metric units): 38.0 Millilitres

Application using EPX dispensing pliers.

An EPX applicator gun, mixing nozzle and plunger for a 10:1 mixing ratio are required for application; see the related tab.

In the case of a small application where you do not wish to spend on an applicator gun, it is sufficient to order only the adhesive and a mixing plunger for extruding the adhesive. After extruding the adhesive using the plunger, manually mix both components in a clean container and apply using a brush, spatula or other tool.

Additional parameters

Category: Adhesives
EAN: 00051128993521
Application: Metal Bonding, Wood bonding, Bonding of plastics including PP and PE, Bonding ceramics
colour: Black
chemical resistance: Very good
UV resistance: Excellent
moisture resistance: Excellent
temperature resistance: -30°C to +80°C
Shape: Methacrylate
Handling strength: 3 hours
Application method: EPX Applicator Guns
Opening hours: 3 minutes
tensile strength: 2400 psi
Peel strength at 24°C: N/A
Shear strength at -55°C: 6 MPa
Shear strength at 24°C: 14 MPa
Shear strength at 82°C: 3 MPa
mixing ratio: 10:1
Industries: Metalworking, Advertisement, Wood processing, General Industry, shipping, construction, Electronics, Medical Products, Consumer Goods

Discussion

Be the first who will post an article to this item!

Do not fill out this field

Security check

Vložením komentáře souhlasíte s podmínkami ochrany osobních údajů