10 Scotch-Weld polychloroprene contact adhesive for bonding rubber, foams, leathers, technical textiles, 1 litre

Code: 7000080206
€47,60 / pcs €39,30 excl. VAT Measure price:
in stock (2 pcs)
Delivery to:
20.11.2026
Delivery options

3M Scotch-Weld Polychloroprene Contact Adhesive - Bonding Rubbers, Foams, Leathers, Technical Textiles, 1 Litre

Detailed information

Product detailed description

3M Scotch-Weld Polychloroprene Contact Adhesive - Bonding Rubbers, Foams, Leathers, Technical Textiles, 1 Litre

3M™ 10 is a versatile solvent-based neoprene contact adhesive, available in a tube, can or bucket.

It offers high immediate handling strength and good resistance to high temperatures and is commonly used for bonding most metals and plastics. It is also suitable for bonding large-area panels or composite laminates.

  • Bonding sheets, such as stainless steel, aluminium, cold-rolled steel, and various types of plastics to other substrates
  • Highly efficient laminating adhesive
  • Excellent resistance to moisture and high temperatures up to 148 °C
  • Excellent resistance to moisture and high temperatures up to 148 °C

• Application by roller or brush.
• Fast drying.
• Adhesion to a wide range of materials.
• Excellent resistance to plastic flow.
• Working time 60 minutes.
• Meets the requirements of specifications MMM-A-121, MMM-A-130B and A-A-1936A

Viscosity (approx.): 450 - 700 cps
Brookfield RVF viscometer spindle no. 2 at 20 rpm at 27 °C
Solid content (by weight): 21-25 %
Base: Polychloroprene
Colour (wet and dry): Light yellow
Net weight (lb/gal): 6.9 ± 0.2 lb
Flash point (TCC): -25 °C
Solvent: Petroleum distillates, acetone, toluene and n-hexane
Coverage (approx.): 7 m2 per litre (at a dry film weight of 25 g/m2)

Surface preparation
1. To achieve the best results, all bonded surfaces must be dry
and free from contaminants, dust, oils, loose paint, wax, lubricant etc.
2. Oil, grease and other contaminants can be removed by wiping with a solvent, such as
methylethylketone.*
3. If the adhesive is used on decorative laminates, the laminate must first reach
moisture equilibrium for the workshop conditions.
Working Temperature
1. The temperature of the adhesive and the surfaces to be joined must be at least 18 °C.
2. Warm the can of adhesive by placing it in a warm room, not in an oven or on
a stove or any other potential ignition source.
3. If the room must be heated, turn off the heating before opening the package.
4. Keep the heating off until all vapours have disappeared.
Usage
1. Mix thoroughly before use.
2. Apply a generous, even layer of adhesive to both surfaces using a brush
with natural fibres or animal hair. The applied adhesive can also be spread with a painting
roller (use a textured type that is durable against solvents).
3. Porous surfaces may require two coats of adhesive.
4. A glossy film after complete drying is an indication of sufficient amount of adhesive.
5. Matte areas in the dry adhesive indicate an insufficient amount of adhesive; these areas
must be recoated.
Joining
1. Allow surfaces to dry until the adhesive no longer feels tacky (5-10 minutes).
2. Carefully prepare the surfaces in the correct position before joining.
3. Once the bonded surfaces make contact, their relative position cannot be changed.
4. You may use spacers, such as pins or strips of laminate, to prevent
premature contact of adhesive to adhesive and subsequent bonding.
5. Then remove the spacers and press the bonded parts evenly towards the edges.
6. A 76 mm wide roller and maximum pressure should be used to ensure contact between both
surfaces and the formation of a bond, especially at the edges.
7. Bonded parts can be machined, trimmed or finished immediately after joining.
Drying time
1. Drying time depends on temperature, humidity, air movement and the porosity of the bonded materials.
Cleaning
1. Excess adhesive can be removed with a solvent, such as methyl ethyl ketone.*
* When using solvents, remove all sources of ignition and follow the safety
instructions and manufacturer guidelines for use.

Additional parameters

Category: Adhesives
EAN: 4046719305988
Application: Bonding of rubber, foams, leather, technical textiles, etc. to metals, wood, ceramics and other materials, Creating flexible bonded joints
colour: Light Yellow
chemical resistance: Excellent
UV resistance: Excellent
moisture resistance: Excellent
temperature resistance: -30°C to 105°C
Shape: Polychloroprene
Joint type: Permanent
Application method: With a roller or brush
Flammable fuel: Yes
Flammable solvents: Yes
Aggregation: Liquid
Yield: 7 m2 per litre (at a dry film weight of 25 g/m2 )
Appearance/Odour: Light yellow / Solvent odour
Base material: Polychloroprene
Ignition point: -25 °C
Density (g/ml): 450 - 700 cps

Discussion

Be the first who will post an article to this item!

Do not fill out this field

Security check

Vložením komentáře souhlasíte s podmínkami ochrany osobních údajů